View LT3651-42_5035957.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LT3651-4.2 Monolithic 4A High Voltage Li-Ion Battery Charger FEATURES
n n n n n n n n n n n n n n n
DESCRIPTION
The LT(R)3651 is a 4A Li-Ion/Polymer battery charger that operates over a 4.8V to 32V input voltage range. An efficient monolithic average current mode synchronous switching regulator provides constant current, constant voltage charging with programmable maximum charge current. A charging cycle starts with battery insertion or when the battery voltage drops 2.5% below the float voltage. Charger termination is selectable as either charge current or internal safety timer timeout. Charge current termination occurs when the charge current falls to onetenth the programmed maximum current (C/10). Timer based termination is typically set to three hours and is user programmable (charging continues below C/10 until timeout). Once charging is terminated, the LT3651 supply current drops to 85A into a standby mode. The LT3651 offers several safety features. A discharged battery is preconditioned with a small trickle charge and generates a signal if unresponsive. A thermistor monitors battery temperature, halting charging if out of range. Excessive die temperature reduces charge current. Charge current is also reduced to maintain constant input current to prevent excessive input loading. The LT3651 is available in a 5mm x 6mm 36-pin QFN package.
Wide Input Voltage Range: 4.8V to 32V (40V Absolute Maximum) Programmable Charge Current Up to 4A Selectable C/10 or Onboard Timer Termination Dynamic Charge Rate Programming/Soft-Start Programmable Input Current Limit 0.5% Float Voltage Accuracy 7.5% Charge Current Accuracy 4% C/10 Detection Accuracy NTC Resistor Temperature Monitor Auto-Recharge at 97.5% Float Voltage Auto-Precondition <70% Float Voltage Bad Battery Detection with Auto-Reset Average Current Mode, Synchronous Switcher User Programmable Frequency Low Profile (0.75mm) 5mm x 6mm 36-Pin QFN Package
APPLICATIONS
n n n n
Industrial Handheld Instruments 12V to 24V Automotive and Heavy Equipment Desktop Cradle Chargers Notebook Computers
L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and PowerPath is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners.
TYPICAL APPLICATION
7.5V to 32V Single Cell 4A Charger
VIN 7.5V TO 32V CLP VIN CLN SHDN SW ACPR FAULT BOOST CHRG LT3651-4.2 SENSE RT 54.9k TIMER BAT 100F NTC ILIM RNG/SS GND 22F TO SYSTEM LOAD EFFICIENCY (%) 100 90
VBAT and Efficiency vs IBAT
4.25 VBAT VIN = 10V 4.15
1F 3.3H 1N5819 24m
80 VIN = 20V 70
4.05
VBAT (V)
3.95
60
3.85
+
BATTERY
365142 TA01a
50
0
0.5
1.0
1.5
2.0 IBAT (A)
2.5
3.0
3.75 3.5 4.0
365142 TA01b
365142fa
1
LT3651-4.2 ABSOLUTE MAXIMUM RATINGS
(Note 1)
PIN CONFIGURATION
TOP VIEW RNG/SS GND CLN SW CLP 28 ILIM 27 SHDN 37 26 CHRG 25 FAULT 24 TIMER 23 GND 22 SW 38 21 NC 20 NC 19 NC 11 12 13 14 15 16 17 18 SW SW SW SW SW SW UHE PACKAGE 36-LEAD (5mm x 6mm) PLASTIC QFN SW VIN VIN VIN RT NTC 1 ACPR 2 BAT 3 SENSE 4 BOOST 5 GND 6 SW 7 NC 8 NC 9 NC 10
VIN .......................................................................... 40V CLN, CLP SHDN, CHRG, , FAULT, ACPR ............................... VIN + 0.5V Up to 40V CLP - CLN .............................................................0.5V SW ...........................................................................40V SW - VIN ..................................................................4.5V BOOST ......................................... SW + 10V Up to 50V SENSE, BAT ............................................................ 10V SENSE-BAT ............................................. -0.5V to 0.5V TIMER, RNG/SS, ILIM, NTC, RT .............................. 2.5V Operating Junction Temperature Range (Notes 2, 3) ................................................ -40 to 125C Storage Temperature Range....................... -65 to 150C
36 35 34 33 32 31 30 29
TJMAX = 125C, JA = 43C/W EXPOSED PAD (PIN 37) IS GND, MUST BE SOLDERED TO PCB EXPOSED PAD (PIN 38) IS SW, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LT3651EUHE-4.2#PBF LT3651EUHE-4.2#TRPBF 365142 36-Lead (5mm x 6mm) Plastic QFN -40C to 125C LT3651IUHE-4.2#PBF LT3651IUHE-4.2#TRPBF 365142 36-Lead (5mm x 6mm) Plastic QFN -40C to 125C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
ELECTRICAL CHARACTERISTICS
PARAMETER VIN Operating Range VIN OVLO Threshold VIN OVLO Hysteresis VIN UVLO Threshold VIN UVLO Hysteresis Battery Float Voltage, VBAT(FLT) VIN Rising VIN Rising
The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = 20V, SHDN = 2V, SENSE = BAT = VBAT(FLT), CTIMER = 0.68F RT = 50k, CLP = CLN = VIN, BOOST - SW = 4V. ,
CONDITIONS
l l
MIN 4.8 32
TYP 35 1.1 4.6 0.2
MAX 32 40 4.8 4.22 4.24
UNITS V V V V V V mV V mV
365142fa
l
l
4.18 4.16
4.2 -105 2.9 70
Battery Recharge Voltage Hysteresis Battery Precondition Threshold Voltage, VBAT(PRE) Battery Precondition Threshold Hysteresis
Threshold Voltage Relative to VBAT(FLT) VBAT Rising Threshold Voltage Relative to VBAT(PRE)
2
LT3651-4.2 ELECTRICAL CHARACTERISTICS
PARAMETER Operating VIN Supply Current Top Switch On Voltage Bottom Switch On Voltage BOOST Supply Current BOOST Switch Drive Precondition Current Sense Voltage Input Current Limit Voltage CLP Input Bias Current CLN Input Bias Current ILIM Bias Current System Current Limit Programming Gain Maximum Charge Current Sense Voltage C/10 Trigger Sense Voltage BAT Input Bias Current SENSE Input Bias Current RNG/SS Bias Current Charge Current Limit Programming Gain NTC Range Limit (High) NTC Range Limit (Low) NTC Threshold Hysteresis NTC Disable Impedance NTC Bias Current Shutdown Threshold Shutdown Hysteresis SHDN Input Bias Current Status Low Voltage TIMER Charge/Discharge Current TIMER Disable Threshold Full Charge Cycle Time-Out Precondition Timeout Timer Accuracy Switcher Operating Frequency, fO Minimum SW On-Time, tON(MIN) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LT3651 is tested under pulse loaded conditions such that TJ = TA. The LT3651E is guaranteed to meet performance specifications from 0C to 85C junction temperature. Specifications over the -40C to 125C operating junction temperature range are assured by design, RT = 50k RT = 250k
l l l
The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25C (Note 2). VIN = 20V, SHDN = 2V, SENSE = BAT = VBAT(FLT), CTIMER = 0.68F RT = 50k, CLP = CLN = VIN, BOOST - SW = 4V. ,
CONDITIONS CC/CV Mode, Top Switch On, ISW = 0 Standby Mode Shutdown (SHDN = 0) VIN - VSW , ISW = 4A VSW , ISW = 4A Switch High, ISW = 0, 2.5 < (VBOOST - VSW) < 4.5 IBOOST/ISW , ISW = 4A VSENSE - VBAT , VBAT = 2.5 VCLP - VCLN, ILIM Open
l
MIN
TYP 8.6 80 17 480 140 40 25 14
MAX
UNITS mA A A mV mV mA mA/A mV
70
95 120 36
115
mV nA A
43 88 5.0
50 11.5 95 8.6 0.1 0.1
57 103 12.3 1 1 56 12.5 1.45 0.31
A V/V mV mV A A A V/V V V % k
VILIM/(VCLP - VCLN), VILIM = 0.5V VSENSE - VBAT , VBAT = 3.5, VRNG/SS > 1.1V VSENSE - VBAT Charging Terminated Charging Terminated
l l l
44 8.5 1.25 0.27 150 46.5 1.16
50 10.8 1.36 0.29 10 470 50 1.20 95 -10
VRNG/SS/(VSENSE - VBAT), VRNG/SS = 0.5V VNTC Rising VNTC Falling % of Threshold Minimum External Impedance to GND VNTC = 0.75V VSHDN Rising
l l l
l l l
53.5 1.23
A V mV nA
VCHRG, VFAULT , VACPR, Load = 10mA
l
0.45 25 0.1 0.25 3 22.5 -13 1.1 250 150 13
V A V Hour Minute % MHz kHz ns
characterization and correlation with statistical process controls. The LT3651I is guaranteed over the full -40C to 125C operating junction temperature range. The junction temperature (TJ in C) is calculated from the ambient temperature (TA in C) and power dissipation (PD in Watts) according to the formula: TJ = TA + PD * JA where JA (in C/W) is the package thermal impedance.
365142fa
3
LT3651-4.2 ELECTRICAL CHARACTERISTICS
Note 3: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. The maximum rated junction temperature will be exceeded when this protection is active. Continuous operation above the specified absolute maximum operating junction temperature may impair device reliability or permanently damage the device.
TYPICAL PERFORMANCE CHARACTERISTICS
Battery Float Voltage vs Temperature
1.0 100 95 0.5 VBAT(FLT) (%) IVIN (A) 90 85 80 75 70 65 60 55 -1.0 -50 -25 25 50 75 0 TEMPERATURE (C) 100 125 50 -50 -25 25 50 0 TEMPERATURE (C) 75 100 0 0 0.2 0.4 0.6 0.8 VRNG/SS (V) 1.0 1.2 ICHG(MAX) (%)
VIN Standby Mode Current vs Temperature
120 100 80 60 40 20
Maximum Charge Current vs VRNG/SS as a Percentage of Programmed IMAX
0
-0.5
365142 G01
365142 G02
365142 G03
C/10 Threshold (VSENSE - VBAT) vs Temperature
11 120 100 10 VSENSE - VBAT (mV) IIN(MAX) (%) 80 60 40 8 20 7 -50 0
Maximum Input Current vs VILIM as a Percentage of Programmed IIN(MAX)
9
-25
75 0 25 50 TEMPERATURE (C)
100
125
0
0.2
0.4
0.6 0.8 VILIM (V)
1.0
1.2
365142 G04
365142 G05
365142fa
4
LT3651-4.2 TYPICAL PERFORMANCE CHARACTERISTICS
IMAX Current Limit (VSENSE - VBAT) vs Temperature
101.0 150 100 100.5 VSENSE - VBAT (mV) CURRENT (A) 50 0 -50 -100 -150 -200 -250 -300 99.0 -50 -25 75 0 25 50 TEMPERATURE (C) 100 125 -350 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 VBAT (V)
365142 G07V
SENSE and BAT Pin Current vs BAT Voltage, VSENSE = VBAT
ISENSE IBAT
100.0
99.5
365142 G06
Thermal Foldback-Charge Current vs Temperature as a Percentage of Programmed ICHG(MAX)
120 100 80 60 40 20 0 100 ICHG (%) 110 120 130 TEMPERATURE (C) 140
365142 G08
Charge Current vs VBAT as a Percentage of Programmed ICHG(MAX)
120 100 80 60 40 20 0
ICHG(MAX) (%)
2.5
3.0
3.5 VBAT (V)
4.0
4.5
365142 G09
365142fa
5
LT3651-4.2 PIN FUNCTIONS
NTC (Pin 1): Battery Temperature Monitor Pin. This pin is used to monitor battery temperature. Typically a 10k NTC (negative temperature coefficient) thermistor (B = 3380) is embedded with the battery and connected from the NTC pin to ground. The pin sources 50A into the resistor and monitors the voltage across the thermistor, regulating charging based on the voltage. If this function is not desired, leave the NTC pin unconnected. ACPR (Pin 2): Open-Collector AC Present Status Pin. This pin sinks current to indicate that VIN is valid and the charger is on. Typically a resistor pull-up is used on this pin. This pin can be pulled up to voltages as high as VIN when disabled, and can sink currents up to 10mA when enabled. BAT (Pin 3): Battery Voltage Monitor Pin. This pin monitors battery voltage. A Kelvin connection is made to the battery from this pin and a decoupling capacitor (CBAT) is placed from this pin to ground. The charge function operates to achieve the final float voltage at this pin. The auto-restart feature initiates a new charging cycle when the voltage at the BAT pin falls 2.5% below this float voltage. Once the charge cycle is terminated, the input bias current of the BAT pin is reduced to <0.1A to minimize battery discharge while the charger remains connected. SENSE (Pin 4): Charge Current Sense Pin. The charge current is monitored with a sense resistor (RSENSE) connected between this pin and the BAT pin. The inductor current flows through RSENSE to the battery. The voltage across this resistor sets the average charge current. The maximum average charge current (IMAX) corresponds to 95mV across the sense resistor. BOOST (Pin 5): Bootstrapped Supply Rail for Switch Drive. This pin facilitates saturation of the high side switch transistor. Connect a 1F or greater capacitor from the BOOST pin to the SW pin. The operating range of this pin is 0V to 4.5V, referenced to the SW pin when the switch is high. The voltage on the decoupling capacitor is refreshed through a rectifying diode, with the anode connected to either the battery output voltage or an external source, and the cathode connected to the BOOST pin. GND (Pins 6, 23, 31, 37): Ground. These pins are the ground pins for the part. Pins 31 and 37 must be connected together. Pins 6 and 23 are connected via the leadframe to the exposed backside Pin 37. Solder the exposed backside to the PCB for good thermal and electrical connection. SW (Pins 7, 11-18, 22, 38): Switch Output Pin. This pin is the output of the charger switches. An inductor is connected between this pin and the SENSE pin. When the switcher is active, the inductor is charged by the high side switch from VIN and discharged by the bottom side switch to GND. Solder the exposed backside, Pin 38, to the PCB for good thermal connection. TIMER (Pin 24): End-Of-Cycle Timer Programming Pin. A capacitor on this pin to ground determines the full charge end-of-cycle time. Full charge end-of-cycle time is programmed with this capacitor. A 3 hour charge cycle is obtained with a 0.68F capacitor. This timer also controls the bad battery fault that is generated if the battery does not reach the precondition threshold voltage within one-eighth of a full cycle (22.5 minutes for a 3 hour charge cycle). The timer based termination is disabled by connecting the TIMER pin to ground. With the timer function disabled, charging terminates when the charge current drops below a C/10 rate, or approximately 10% of maximum charge rate. FAULT (Pin 25): Open-Collector Fault Status Output. This pin indicates charge cycle fault conditions during a battery charging cycle. Typically a resistor pull-up is used on this pin. This status pin can be pulled up to voltages as high as VIN when disabled, and can sink currents up to 10mA when enabled. A temperature fault causes this pin to be pulled low. If the internal timer is used for termination, a bad battery fault also causes this pin to be pulled low. If no fault conditions exist, the FAULT pin remains high impedance.
365142fa
6
LT3651-4.2 PIN FUNCTIONS
CHRG (Pin 26): Open-Collector Charger Status Output. This pin indicates the battery charging status. Typically a resistor pull-up is used on this pin. This status pin can be pulled up to voltages as high as VIN when disabled, and can sink currents up to 10mA when enabled. CHRG is pulled low during a battery charging cycle. When the charge cycle is terminated, the CHRG pin becomes high impedance. If the internal timer is used for termination, the pin stays low during the charging cycle until the charge current drops below a C/10 rate, or approximately 10% of the maximum charge current. A temperature fault also causes this pin to be pulled low. SHDN (Pin 27): Shutdown Pin. This pin can be used for precision UVLO functions. When this pin rises above the 1.20V threshold, the part is enabled. The pin has 95mV of voltage hysteresis. When in shutdown mode, all charging functions are disabled. When the SHDN pin is pulled below 0.4V, the IC enters a low current shutdown mode where the VIN pin current is reduced to 17A. Typical SHDN pin input bias current is 10nA. Connect the pin to VIN if the shutdown function is not desired. ILIM (Pin 28): Input Current Limit Programming This pin allows for setting and dynamic adjustment of the system input current limit, and can be used to employ a soft-start function. The voltage on this pin sets the maximum input current by setting the maximum voltage across the input current sense resistor, placed between CLP and CLN. The effective range on the pin is 0V to 1V. 50A is sourced from this pin usually to a resistor (RILIM) to ground. VIILIM represents approximately 11 times the maximum voltage across the input current sense resistor. If no RILIM is used the part will default to maximum input current. Soft-start functionality for input current can be implemented with a capacitor (CILIM) from ILIM to ground. The soft-start capacitor and the programming resistor can be implemented in parallel. CLP/CLN (Pin 29/Pin 30): System Current Limit Positive and Negative Input. System current levels are monitored by connecting a sense resistor from the input power supply to the CLP pin, connecting a sense resistor from the CLP pin to the CLN pin and then connecting CLN to VIN. The system load is then delivered from the CLN pin. The LT3651 servos the maximum charge current required to maintain programmed maximum system current. The system current limit is set as a function of the voltage on the ILIM pin and the input current sense resistor. This function is disabled by shorting CLP CLN and VIN together. , VIN (Pins 32, 33, 34): Charger Input Supply. This pin provides power for the LT3651. Charge current for the battery flows into this pin. IVIN is less than 100A after charge termination. Connect both pins together. RNG/SS (Pin 35): Charge Current Range and Soft-Start Pin. This pin allows for setting and dynamic adjustment of the maximum charge current, and can be used to employ a soft-start function. The voltage on this pin sets the maximum charge current by setting the maximum voltage across the charge current sense resistor, RSENSE , placed between SENSE and BAT. The effective range on the pin is 0V to 1V. 50A is sourced from this pin usually to a resistor (RRNG/SS) to ground. VRNG/SS represents approximately 10 times the maximum voltage across the charge current sense resistor. If no RRNG/ SS is used the part will default to maximum charge current. Soft-start functionality for charge current can be implemented by connecting a capacitor (CRNG/SS) from RNG/SS to ground. The soft-start capacitor and the programming resistor can be implemented in parallel. The RNG/SS pin is pulled low during fault conditions, allowing graceful recovery from faults if CRNG/SS is used. RT (Pin 36): Switcher Oscillator Timer Set Pin. A resistor from this pin to ground sets the switcher oscillator frequency. Typically this is 54.9k for fOSC = 1MHz.
365142fa
7
LT3651-4.2 BLOCK DIAGRAM
50A ILIM CLN CLP RT TIMER TIMER OSC
28 30 29 36 24
A12 OSC 0.2V
R LATCH SQ
A13
A11
+ -
A10
A14
RIPPLE COUNTER COUNT RESET COUNT
+ -
125C TJ VC REV CUR INHIBIT
STANDBY A9
26 25
CHRG FAULT
COUNT RESET MODE ENABLE (TIMER OR C/10) CONTROL LOGIC TERMINATE SS/RESET STATUS C/10
0.3V
ITH 10RS SS/RESET
PRECONDITION NTC
VINT 2.7V x2.25
+
1.2V A4
+
4.2V
+
4.1V
50A 1.36V
+ - - +
A1
STANDBY
A2 A3
+ -
TERMINATE ACPR
1.3V 46A
8
-+
1
NTC
0.29V
2.4V
+ -
A5
0.7V GND 6, 23, 31, 37
365142 BD
+ -
A6
+ -
+ -
A8
50A 0.1V 1V
+
+
0.15V A7
+ -
-+ +
+ -
C-EA
+ -
+
+ -
+ -
STANDBY
UVLO
BOOST 4.6V OVLO
+ -
5
35V
VIN 32, 33, 34
+
SW 7, 11-18, 22, 38 VIN
+-
RS RS V-EA
SENSE BAT
4 3
RNG/SS
35
2.9V
SHDN
27
2
365142fa
LT3651-4.2 OPERATION
Overview The LT3651 is a complete Li-Ion battery charger, addressing wide input voltage (4.8V to 32V) and high currents (up to 4A). High charging efficiency is produced with a constant frequency, average current mode synchronous step-down switcher architecture. The charger includes the necessary circuitry to allow for programming and control of constant current, constant voltage (CC/CV) charging with both current only and timer termination. High charging efficiency is achieved by the switcher by using a bootstrapped supply for low switch drop for the high side driver and a MOSFET for the low side (synchronous) switch. Maximum charge current is set with an external sense resistor in series with the inductor and is adjustable through the RNG/SS pin. Total system input current is monitored with an input sense resistor and is used to maintain constant input current by regulating battery charge current. It is adjustable through the ILIM pin. If the battery voltage is low, charge current is automatically reduced to 15% of the programmed current to provide safe battery preconditioning. Once the battery voltage climbs above the battery precondition threshold, the IC automatically increases the maximum charge current to the full programmed value. Charge termination can occur when charge current decreases to one-tenth the programmed maximum charge current (C/10 termination). Alternately, termination can be time based through the use of an internal programmable charge cycle control timer. When using the timer termination, charging can continue beyond the C/10 level to "top-off" a battery. Charging typically terminates three hours after initiation. When the timer-based scheme is used, bad battery detection is also supported. A system fault is triggered if a battery stays in precondition mode for more than one-eighth of the total charge cycle time. Once charging is terminated and the LT3651 is not actively charging, the IC automatically enters a low current standby mode in which supply bias currents are reduced to <85A. If the battery voltage drops 2.5% from the full charge float voltage, the LT3651 engages an automatic charge cycle restart. The IC also automatically restarts a new charge cycle after a bad battery fault once the failed battery is removed and replaced with another battery. After charging is completed the input bias currents on the pins connecting to the battery are reduced to minimize battery discharge. The LT3651 contains provisions for a battery temperature monitoring circuit. Battery temperature is monitored by using a NTC thermistor located with the battery. If the battery temperature moves outside a safe charging range of 0C to 40C the charging cycle suspends and signals a fault condition. The LT3651 contains two digital open-collector outputs, which provide charger status and signal fault conditions. These binary coded pins signal battery charging, standby or shutdown modes, battery temperature faults and bad battery faults. A precision undervoltage lockout is possible by using a resistor divider on the shutdown pin (SHDN). The input supply current is 17A when the IC is in shutdown. General Operation (See Block Diagram) The LT3651 uses an average current mode control loop architecture to control average charge current. The LT3651 senses charger output voltage via the BAT pin. The difference between this voltage and the internal float voltage reference is integrated by the voltage error amplifier (V-EA). The amplifier output voltage (ITH) corresponds to the desired average voltage across the inductor sense resistor, RSENSE, connected between the SENSE and BAT pins. The ITH voltage is divided down by a factor of 10, and provides a voltage offset on the input of the current error amplifier (C-EA). The difference between this imposed voltage and the current sense resistor voltage is integrated by C-EA. The resulting voltage (VC) provides a voltage that is compared against an internally generated ramp and generates the switch duty cycle that controls the charger's switches. The ITH error voltage corresponds linearly to average current sensed across the inductor current sense resistor. Maximum charge current is controlled by clamping the maximum voltage of ITH to 1V. This limits the maximum current sense voltage (voltage across RSENSE) to 95mV
365142fa
9
LT3651-4.2 OPERATION
setting the maximum charge current. Manipulation of maximum charge current is possible through the RNG/SS and ILIM pins (see the RNG/SS: Dynamic Charge Current Adjust, RNG/SS: Soft-Start and ILIM Control sections). If the voltage on the BAT pin (VBAT) is below VBAT(PRE), A7 initiates the precondition mode. During the precondition interval, the charger continues to operate in constant current mode, but the ITH clamp is reduced to 0.15V reducing charge current to 15% of the maximum programmed value. As VBAT approaches the float voltage (VFLOAT) the voltage error amp V-EA takes control of ITH and the charger transitions into constant voltage (CV) mode. As this occurs, the ITH voltage falls from the limit clamp and charge current is reduced from the maximum value. When the ITH voltage falls below 0.1V, A8 signals C/10. If the charger is configured for C/10 termination the charge cycle is terminated. Once the charge cycle is terminated, the CHRG status pin becomes high impedance and the charger enters low current standby mode. The LT3651 contains an internal charge cycle timer that terminates a successful charge cycle after a programmed amount of time. This timer is typically programmed to achieve end-of-cycle in three hours, but can be configured for any amount of time by setting an appropriate timing capacitor value (CTIMER). When timer termination is used, the charge cycle does not terminate after C/10 is achieved. Because the CHRG status pin responds to the C/10 current level, the IC will indicate a fully charged battery status, but the charger will continue to source low currents. At the programmed end of the cycle time the charge cycle stops and the part enters standby mode. If the battery did not achieve at least 97.5% of the full float voltage at the end-of-cycle, charging is deemed unsuccessful and another full-timer cycle is initiated. Use of the timer function also enables bad battery detection. This fault condition is achieved if the battery does not respond to preconditioning and the charger remains in (or enters) precondition mode after one-eighth of the programmed charge cycle time. A bad battery fault halts the charging cycle, the CHRG status pin goes high impedance and the FAULT pin is pulled low. When the LT3651 terminates a charging cycle, whether through C/10 detection or by reaching timer end-of-cycle, the average current mode analog loop remains active but the internal float voltage reference is reduced by 2.5%. Because the voltage on a successfully charged battery is at the full float voltage, the voltage error amp detects an overvoltage condition and rails low. When the voltage error amp output drops below 0.3V, the IC enters standby mode, where most of the internal circuitry is disabled and the VIN bias current is reduced to <100A. When the voltage on the BAT pin drops below the reduced float reference level, the output of the voltage error amp will climb, at which point the IC comes out of standby mode and a new charging cycle is initiated. The system current limit allows charge current to be reduced in order to maintain a constant input current. Input current is measured via a resistor (RCL) that is placed between the CLP and CLN pins. Power is applied through this resistor and is used to supply both VIN of the chip and other system loads. An offset produced on the inputs of A12 sets the threshold. When that threshold is achieved, ITH is reduced, lowering the charge current thus maintaining the maximum input current. 50A of current is sourced from ILIM to a resistor (RILIM) that is placed from that pin to ground. The voltage on ILIM determines the regulating voltage across RCL. 1V on ILIM corresponds to 95mV across RCL. The ILIM pin clamps internally to 1V maximum. If the junction temperature of the die becomes excessive, A10 activates decreasing ITH and reduces charge current. This reduces on-chip power dissipation to safe levels but continues charging.
365142fa
10
LT3651-4.2 APPLICATIONS INFORMATION
OSC Frequency A precision resistor to ground sets the LT3651 switcher oscillator frequency, fOSC, permitting user adjustability of the frequency value. Typically this frequency is in the 200kHz to 1MHz range. Power consideration may necessitate lower frequency operation especially if the charger is operated with very high voltages. Adjustability also allows the user to position switching harmonics if their system requires. The timing resistor, RT , value is set by the following: 54.9 RT = (k)t fOSC (MHz ) Set RT to 54.9k for 1MHz operation. VIN Input Supply The LT3651 is biased directly from the charger input supply through the VIN pin. This supply provides large switched currents, so a high quality, low ESR decoupling capacitor is required to minimize voltage glitches on VIN. The VIN decoupling capacitor (CVIN) absorbs all input switching ripple current in the charger. Size is determined by input ripple voltage with the following equation: CIN(BULK) = IMAX * VBAT (F ) fOSC (MHz ) * VIN * VIN Boost Supply The BOOST bootstrapped supply rail drives the internal switch and facilitates saturation of the high side switch transistor. The BOOST voltage is normally created by connecting a 1F capacitor from the BOOST pin to the SW pin. Operating range of the BOOST pin is 2V to 4.5V, as referenced to the SW pin. The boost capacitor is normally charged via a diode connected from the battery or an external source through the low side switch. Rate the diode average current greater than 0.1A and its reverse voltages greater than VIN(MAX). If an external supply that is greater than the input is available (VBOOST - VIN > 2V), it may be used in place of the bootstrap capacitor and diode. VIN ,VBOOST Start-Up Requirement The LT3651 operates with a VIN range of 4.8V to 32V. The charger begins a charging cycle when the detected battery voltage is below the 4.1V auto-restart float voltage and the part is enabled. When VIN is below 6.3V and the BOOST capacitor is uncharged, the high side switch would normally not have sufficient head room to start switching. During normal operation the low side switch is deactivated when charge current is very low to prevent reverse current in the inductor. However in order to facilitate start-up, the LT3651 enables the switch if VBOOST voltage is low. This allows initial charging of the BOOST capacitor which then permits the high side switch to saturate and efficiently operate. The boost capacitor charges to full potential after a few cycles. The design should consider that as the switcher turns on and input current increases, input voltage drops due to source input impedance and input capacitance. This potentially allows the input voltage to drop below the internal VIN UVLO turn-on and thus disrupt normal behavior and potentially stall start-up. If an input current sense resistor is used, its drop must be considered as well. These problems are worsened because input current is largest at low input voltage. Pay careful attention to drops in the power path. Adding a soft-start capacitor to the RNG/SS pin and setting UVLO with the SHDN pin is required at low VIN.
365142fa
where VIN is the input ripple, IMAX is the maximum charge current and f is the oscillator frequency. A good starting point for VIN is 0.1V. Worst-case conditions are with VBAT high and VIN at minimum. So for a 8V VIN(MIN), IMAX = 4A and a 1MHz oscillator frequency: 4 * 4.2 CIN(BULK) = = 21F 1* 0.1* 8 The capacitor must have an adequate ripple current rating. RMS ripple current, ICVIN(RMS) is approximated by: V VIN ICVIN(RMS) ICHARGE(MAX) * BAT * -1 VIN VBAT which has a maximum at VIN = 2 * VBAT , where ICVIN(RMS) = ICHARGE(MAX)/2. In the example above that requires a capacitor RMS rating of 2A.
11
LT3651-4.2 APPLICATIONS INFORMATION
BAT Output Decoupling It is recommended that the LT3651 charger output have a decoupling capacitor. If the battery can be disconnected from the charger output this capacitor is required. The value of this capacitor (CBAT) is related to the minimum operational VIN voltage such that: 350F CBAT 20F + VIN(MIN) The voltage rating on CBAT must meet or exceed the battery float voltage. RSENSE: Charge Current Programming The LT3651 charger is configurable to charge at average currents as high as 4A (see Figure 1). If RNG/SS maximum voltage is not limited, the inductor sense resistor, RSENSE, has 95mV across it at maximum charge current so: RSENSE = 0.095V IMAX(AVG) Inductor Selection The primary criteria for inductor value selection in the LT3651 charger is the ripple current created during switching. Ripple current, IMAX, is typically set within a range of 25% to 35% of the maximum charge current, IMAX. This percentage typically gives a good compromise between losses due to ripple and inductor size. An approximate formula for inductance is: L= VBAT + VF V + VF * 1- BAT (H) IMAX * fOSC (MHz ) VIN + VF
Worse-case ripple is at high VIN and high VBAT . VF is the forward voltage of the synchronous switch (approximately 0.14V at 4A). Figure 2 shows inductance for the case of a 4A charger. The inductor must have a saturation current equal to or exceeding the maximum peak current in the inductor. Peak current is IMAX + IMAX/2. Magnetics vendors typically specify inductors with maximum RMS and saturation current ratings. Select an inductor that has a saturation current rating at or above peak current, and an RMS rating above IMAX. Inductors must also meet a maximum volt-second product requirement. If this specification is not in the data sheet of an inductor, consult the vendor to make sure the maximum volt-second product is not being exceeded by your design. The minimum required volt-second product is approximately: V * 1- BAT ( V * s ) fOSC(MHz) VIN(MAX) VBAT
4
where IMAX(AVG) is the maximum average charge current. RSENSE is 24m for a 4A charger.
SW BOOST LT3651-4.2 CS RSENSE BAT
+
365142 F01
Figure 1. Programming Maximum Charge Current Using RSENSE
L (H)
3
2
1 IMAX = 4A fOSC = 1MHz 25% TO 35% RIPPLE 5 10 20 15 VIN(MAX) (V) 25 30
36512 F02
0
Figure 2. Inductance (L) vs Maximum VIN
365142fa
12
LT3651-4.2 APPLICATIONS INFORMATION
System Input Current Limit The LT3651 contains a PowerPathTM control feature to help manage supply load currents. The charger adjusts charger output current in response to a system load so as to maintain a constant input supply load. If overall input supply current exceeds the programmed maximum value the charge current is diminished in an attempt to keep supply current constant. One application where this is helpful is if you have a current limited input supply. Setting the maximum input current limit below the supply limit prevents supply collapse. A resistor, RCL, is placed between the input supply and the system and charger loads as shown in Figure 3. The LT3651 sources 50A from the ILIM pin, so a voltage is developed by simply connecting a resistor to ground. The voltage on the ILIM pin corresponds to 11.5 times the maximum voltage across the input sense resistor (RCL). Input current limit is defined by: VILIM 50A * RILIM IINPUT(MAX) = = 11.5 * RCL 11.5 * RCL
INPUT SUPPLY CLP LT3651-4.2 CLN VIN ILIM RLIM
365142 F03
The programming range for ILIM is 0V to 1V. Voltages higher than 1V have no effect on the maximum input current. The default maximum sense voltage is 95mV and is obtained if RILIM is greater than 20k or if the pin is left open. For example, say you want a maximum input current of 2A and the charger is designed for 4A maximum average charge current, which is 1A VIN referred (4A time duty cycle). Using the full ILIM range, the maximum voltage across RCL is 95mV. So RCL is set at 95mV/2A = 48m. When the system load exceeds 1A (= 2A - 1A) charge current is reduced such that the total input current stays at 2A. When the system load is 2A the charge current is 0. This feature only controls charge current so if the system load exceeds the maximum limit and no other limitation is designed, the input current exceeds the maximum desired, though the charge current reduces to 0A. When the input limiter reduces charge current it does not impact the internal system timer if used. See Figure 4. If reduced voltage overhead or better efficiency is required then reduce the maximum voltage across RCL. So for instance, a 10k RILIM sets the maximum RCL voltage to 43mV. This reduction comes at the expense of slightly increased limit variation.
RCL SYSTEM LOAD CURRENT (A)
3
INPUT CURRENT 2
1
Figure 3. Input Current Limit Configuration
0 0
CHARGE CURRENT (VIN REFERRED)
2 1 SYSTEM LOAD CURRENT (A)
365142 F04
Figure 4. Input Current Limit for 4A Maximum Charger and 6A System Current Limit
365142fa
13
LT3651-4.2 APPLICATIONS INFORMATION
Note the LT3651 internally integrates the input limit signals. This should normally provide sufficient filtering and reduce the sensitivity to current spikes. For the best accuracy take care in provide good Kelvin connections from RCL to CLP CLN. , Further flexibility is possible by dynamically altering the ILIM pin. Different resistor values could be switched in to create unique input limit conditions. The ILIM pin can also be tied to a servo amplifier for other options. See the information in the following section concerning IRNG/SS programming for examples. RNG/SS: Dynamic Current Adjust The RNG/SS pin gives the user the capability to adjust maximum charge current dynamically. The part sources 50A from the pin, so connecting a resistor to ground develops a voltage. The voltage on the RNG/SS pin corresponds to ten times the maximum voltage across the charge current sense resistor, RSENSE. The defining equations for charge current are: IMAX(RNG/SS) = VRNG/SS 50A * RRNG/SS = 10.8 * RSENSE 10.8 * RSENSE
LT3651-4.2 RNG/SS 10k LOGIC HIGH = HALF CURRENT
365142 F05
Figure 5. Using the RNG/SS Pin for Digital Control of Maximum Charge Current
LT3651-4.2 RNG/SS
+ -
365142 F06
SERVO REFERENCE
Figure 6. Driving the RNG/SS Pin with a Current-Sink Active Servo Amplifier
RNG/SS: Soft-Start Soft-start functionality is also supported by the RNG/SS pin. The 50A sourced from the RNG/SS pin can linearly charge a capacitor, CRNG/SS, connected from the RNG/SS pin to ground (see Figure 7). The maximum charge current follows this voltage. Thus, the charge current increases from zero to the fully programmed value as the capacitor charges from 0V to 1V. The value of CRNG/SS is calculated based on the desired time to full current (tSS) following the relation: CRNG/SS = 50A * tSS The RNG/SS pin is pulled to ground internally when charging is terminated so each new charging cycle begins with a soft-start cycle. RNG/SS is also pulled to ground during bad battery and NTC fault conditions, so a graceful recovery from these faults is possible.
IMAX(RNG/SS) is the maximum charge current. The programming range for RNG/SS is 0V to 1V. Voltages higher than 1V have no effect on the maximum charge current. The default maximum sense voltage is 95mV and is obtained if RRNG/SS is greater than 20k or if the pin is left open. For example, say you want to reduce the maximum charge current to 50% of the maximum value. Set RNG/SS to 0.5V (50% of 1V), imposing a 46mV maximum sense voltage. Per the above equation, 0.5V on RNG/SS requires a 10k resistor. If the charge current needs to be dynamically adjustable then Figure 5 shows one method. Active servos can also be used to impose voltages on the RNG/SS pin, provided they can only sink current. Active circuits that source current cannot be used to drive the RNG/SS pin. An example is shown in Figure 6.
LT3651-4.2 RNG/SS CRNG/SS
365142 F07
Figure 7. Using the RNG/SS Pin for Soft-Start
365142fa
14
LT3651-4.2 APPLICATIONS INFORMATION
Status Pins The LT3651 reports charger status through two opencollector outputs, the CHRG and FAULT pins. These pins can accept voltages as high as VIN, and can sink up to 10mA when enabled. The CHRG pin indicates that the charger is delivering current at greater than a C/10 rate, or one-tenth of the programmed maximum charge current. The FAULT pin signals bad battery and NTC faults. These pins are binary coded, and signal state following the table below. On indicates the pin pulled low, and Off indicates pin high impedance.
Table 1. Status Pins State Table
STATUS PINS STATE CHRG Off Off On On FAULT Off On Off On CHARGER STATUS Not Charging--Standby or Shutdown Mode Bad Battery Fault (Precondition Timeout/EOC Failure) Normal Charging at C/10 or Greater NTC Fault (Pause)
Timer Termination The LT3651 supports a timer-based termination scheme, in which a battery charge cycle is terminated after a specific amount of time elapses. Timer termination is engaged when a capacitor (CTIMER) is connected from the TIMER pin to ground. The timer cycle end-of-cycle (tEOC) occurs based on CTIMER following the relation: C TIMER = tEOC (Hrs) * 0.68 (F ) 3
so a typical 3 hour timer end-of-cycle would use a 0.68F capacitor. The CHRG status pin continues to signal charging at a C/10 rate, regardless of which termination scheme is used. When timer termination is used, the CHRG status pin is pulled low during a charge cycle until the charger output current falls below the C/10 threshold. The charger continues to "top off" the battery until timer end-of-cycle, when the LT3651 terminates the charge cycle and enters standby mode. Termination at the end of the timer cycle only occurs if the charge cycle was successful. A successful charge cycle occurs when the battery is charged to within 2.5% of the full-charge float voltage. If a charge cycle is not successful at end-of-cycle, the timer cycle resets and charging continues for another full-timer cycle. When VBAT drops below 97.5% of the full-charge float voltage, whether by battery loading or replacement of the battery, the charger automatically re-engages and starts charging. Precondition and Bad Battery Fault A LT3651 charger has a precondition mode, in which charge current is limited to 15% of the programmed IMAX, as set by RSENSE. The precondition current corresponds to 14mV across RSENSE. Precondition mode is engaged while the voltage on the BAT pin is below the precondition threshold (VBAT(PRE)). Once the BAT voltage rises above the precondition threshold, normal full-current charging can commence. The LT3651 incorporates 2.5% of threshold for hysteresis to prevent mode glitching.
365142fa
C/10 Termination The LT3651 supports a low current based termination scheme, where a battery charge cycle terminates when the current output from the charger falls to below onetenth the maximum current, as programmed with RSENSE. The C/10 threshold current corresponds to 9mV across RSENSE. This termination mode is engaged by shorting the TIMER pin to ground. When C/10 termination is used, a LT3651 charger will source battery charge current as long as the average current level remains above the C/10 threshold. As the full-charge float voltage is achieved, the charge current falls until the C/10 threshold is reached, at which time the charger terminates and the LT3651 enters standby mode. The CHRG status pin follows the charge cycle and is high impedance when the charger is not actively charging. When VBAT drops below 97.5% of the full-charged float voltage, whether by battery loading or replacement of the battery, the charger automatically re-engages and starts charging. There is no provision for bad battery detection if C/10 termination is used.
15
LT3651-4.2 APPLICATIONS INFORMATION
When the internal timer is used for termination, bad battery detection is engaged. This fault detection feature is designed to identify failed cells. A bad battery fault is triggered when the voltage on BAT remains below the precondition threshold for greater than one-eighth of a full timer cycle (one-eighth end-of-cycle). A bad battery fault is also triggered if a normally charging battery re-enters precondition mode after one-eighth end-of-cycle. When a bad battery fault is triggered, the charge cycle is suspended, so the CHRG status pin becomes high impedance. The FAULT pin is pulled low to signal a fault detection. The RNG/SS pin is also pulled low during this fault, to accommodate a graceful restart, in the event that a soft-start function is incorporated (see the RNG/SS: Soft-Start section). Cycling the charger's power or SHDN function initiates a new charge cycle, but a LT3651 charger does not require a reset. Once a bad battery fault is detected, a new timer charge cycle initiates when the BAT pin exceeds the precondition threshold voltage. During a bad battery fault, 1mA is sourced from the charger. Removing the failed battery allows the charger output voltage to rise and initiate a charge cycle reset. In that way removing a bad battery resets the LT3651. A new charge cycle is started by connecting another battery to the charger output. Battery Temperature Fault: NTC The LT3651 can accommodate battery temperature monitoring by using an NTC (negative temperature coefficient) thermistor close to the battery pack. The temperature monitoring function is enabled by connecting a 10k, B = 3380 NTC thermistor from the NTC pin to ground. If the NTC function is not desired, leave the pin unconnected. The NTC pin sources 50A and monitors the voltage dropped across the 10k thermistor. When the voltage on this pin is above 1.36V (0C) or below 0.29V (40C), the battery temperature is out of range, and the LT3651 triggers an NTC fault. The NTC fault condition remains until the voltage on the NTC pin corresponds to a temperature within the 0C to 40C range. Both hot and cold thresholds incorporate hysteresis that corresponds to 2.5C. During an NTC fault, charging is halted and both status pins are pulled low. If timer termination is enabled, the timer count is suspended and held until the fault condition is relieved. The RNG/SS pin is also pulled low during this fault, to accommodate a graceful restart in the event that a soft-start function is being incorporated (see the RNG/ SS: Soft-Start section). If higher operational charging temperatures are desired, the temperature range can be expanded by adding series resistance to the 10k NTC resistor. Adding a 0.91k (0TC) resistor will increase the effective temperature threshold to 45C. Thermal Foldback The LT3651 contains a thermal foldback protection feature that reduces maximum charger output current if the internal IC junction temperature approaches 125C. In most cases, on-chip temperature servos such that any overtemperature conditions are relieved with only slight reductions in maximum charge current. In some cases, the thermal foldback protection feature can reduce charge currents below the C/10 threshold. In applications that use C/10 termination (TIMER = 0V), the LT3651 will suspend charging and enter standby mode until the overtemperature condition is relieved. Layout Considerations The LT3651 switch node has rise and fall times that are typically less than 10ns to maximize conversion efficiency. These fast switch times require care in the board layout to minimize noise problems. The philosophy is to keep the physical area of high current loops small (the inductor charge/discharge paths) to minimize magnetic radiation. Keep traces wide and short to minimize parasitic inductance and resistance and shield fast switching voltage nodes (SW, BOOST) to reduce capacitive coupling. The switched node (SW pin) trace should be kept as short as possible to minimize high frequency noise. The VIN capacitor (CIN) should be placed close to the IC to minimize this switching noise. Short, wide traces on these nodes minimize stray inductance and resistance. Keep the BOOST decoupling capacitor in close proximity to the IC to minimize ringing from trace inductance. Route the SENSE and BAT traces together and keep the traces as short as possible. Shielding these signals from switching noise
365142fa
16
LT3651-4.2 APPLICATIONS INFORMATION
with ground is recommended. Make Kelvin connections to the battery and sense resistor. Keep high current paths and transients isolated from battery ground, to assure an accurate output voltage reference. Effective grounding is achieved by considering switched current in the ground plane, and careful component placement and orientation can effectively steer these high currents such that the battery reference does not get corrupted. Figure 8 illustrates the high current, high speed current loops. When the top switch is enabled (charge loop), current flows from the input bypass capacitor (CIN) through the switch and inductor to the battery positive terminal. When the top switch is disabled (discharge loop), current to the battery positive terminal is provided from ground through the synchronous switch. In both cases, these switched currents return to ground via the output bypass capacitor (CBAT). Power Considerations The LT3651 packaging has been designed to efficiently remove heat from the IC via the Exposed Pad on the backside of the package, which is soldered to a copper footprint on the PCB. This footprint should be made as large as possible to reduce the thermal resistance of the IC case to ambient air. Consideration should be given for power dissipation and overall efficiency in a LT3651 charger. A detailed analysis is beyond the scope of the data sheet, however following are general guidelines. The major components of power loss are: conduction and transition losses of the LT3651 switches; losses in the inductor and sense resistors; and AC losses in the decoupling capacitors. Switch conduction loss is fixed.
BOOST VIN CIN LT3651 CHARGE SW DISCHARGE CBAT
365142 F08
Transition losses are adjustable by changing switcher frequency. Higher input voltages cause an increase in transition losses, decreasing overall efficiency. However transition losses are inversely proportional to switcher oscillator frequency so lowering operating frequency reduces these losses. But lower operating frequency usually requires higher inductance to maintain inductor ripple current (inversely proportional). Inductors with larger values typically have more turns, increasing ESR unless you increase wire diameter making them physically larger. So there is an efficiency and board size trade-off. Secondarily, inductor AC losses increase with frequency and lower ripple reduces AC capacitor losses. The following simple rules of thumb assume a charge current of 4A and battery voltage of 3.6V, with 1MHz oscillator, 25m sense resistor and 3.3H/20m inductor. A 1% increase in efficiency represents a 0.2W reduction in power loss at 85% overall efficiency. One way to do this is to decrease resistance in the high current path. A reduction of 0.2W at 4A requires a 12.5m reduction in resistance. This can be done by reducing inductor ESR. It is also possible to lower the sense resistance (with a reduction in RRNG/SS as well), with a trade-off of slightly less accurate current accuracy. All high current board traces should have the lowest resistance possible. Addition of input current limit sense resistance reduces efficiency. Charger efficiency drops approximately linearly with increasing frequency all other things constant. At 15V VIN there is a 1% improvement in efficiency for every 200kHz reduction in frequency (100kHz to 1MHz); At 28V VIN, 1% for every 100kHz. Of course all of these must be experimentally confirmed in the actual charger.
CBOOST RSENSE
+
BATTERY
Figure 8
365142fa
17
LT3651-4.2 TYPICAL APPLICATIONS
7.5V to 32V 4A Charger with High Voltage Current Foldback
120k SMAZ24 18.2V CLP CLN VIN 1F 3.3H 1N5819 RSENSE 24m CBAT 100F SHDN SW ACPR FAULT BOOST CHRG LT3651-4.2 SENSE RT BAT TIMER NTC ILIM RNG/SS GND RIL 1k SBM540 MAXIMUM CHARGE CURRENT (A) CIN 22F VIN 5
Maximum Charge Current vs VIN
4
3
2
RT 54.9k
1 0
+
BATTERY
365142 TA02a
5
10
15
20 VIN (V)
25
30
35
3651 TA02b
12V to 32V 4A Charger with Low Voltage Current Foldback Using the RNG/SS Pin
5 SBM540 VIN SMAZ9V1 9.1V CIN 22F 1F 3.3H 1N5819 RSENSE 24m CBAT 100F MAXIMUM CHARGE CURRENT (A) BATTERY
365142 TA03a
Maximum Charge Current vs VIN
TO SYSTEM LOAD
CLP
CLN
VIN
4
RT 54.9k
SHDN SW ACPR FAULT BOOST CHRG LT3651-4.2 SENSE RT TIMER BAT NTC ILIM RNG/SS GND
3
2
+
0
10
15
20
68k 5.1k 1F
25 VIN (V)
30
35
3651 TA03b
365142fa
18
LT3651-4.2 TYPICAL APPLICATIONS
7.5V to 32V 4A Charger with Approximately Constant Input Power
SBM540 VIN 8.2V RSENSE 50m CLP CLN VIN SW 1F 3.3H 1N5819 RSENSE 24m CBAT 100F CIN 22F TO SYSTEM LOAD INPUT POWER (W) 25 24 23 22 21 20 19 18 17 16 15 5 10 15 20 VIN (V) 25 30 35
Input Power vs VIN
180k
20k 6.2V 180k RT 54.9k
SHDN ACPR FAULT BOOST CHRG LT3651-4.2 SENSE RT TIMER BAT NTC ILIM RNG/SS GND
+
BATTERY
365142 TA05a
0.1F
22k
365142 TA05b
365142fa
19
LT3651-4.2 PACKAGE DESCRIPTION
(Reference LTC DWG # 05-08-1753 Rev A)
UHE Package Variation: UHE36MA 36-Lead Plastic QFN (5mm x 6mm)
0.70 0.05
5.50 0.05 4.10 0.05 3.50 REF
2.54 0.05 0.25 0.05 3.45 0.05 0.76 0.05
1.52 0.05
3.45 0.05 PACKAGE OUTLINE
0.25 0.05 0.50 BSC 4.50 REF 5.10 0.05 6.50 0.05 RECOMMENDED SOLDER PAD LAYOUT APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED R = 0.10 TYP 3.50 REF 35 PIN 1 NOTCH R = 0.30 TYP OR 0.35 x 45 CHAMFER 36 0.40 0.10 PIN 1 TOP MARK (SEE NOTE 6) 2.54 0.10 3.45 0.10 1 2
5.00 0.10
0.00 - 0.05 0.200 REF
6.00 0.10
4.50 REF
1.52 0.10 3.45 0.10
(UHE36MA) QFN 0410 REV A
0.75 0.05
0.25 0.05
0.50 BSC BOTTOM VIEW--EXPOSED PAD
R = 0.125 TYP
NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.20mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE
365142fa
20
LT3651-4.2 REVISION HISTORY
REV A DATE 01/11 DESCRIPTION Revised Pin 34 to VIN in Pin Configuration, Pin Functions and Block Diagram PAGE NUMBER 2, 6, 7, 8
365142fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
21
LT3651-4.2 TYPICAL APPLICATION
7.5V to 32V 4A Charger with 3-Hour Charge Timeout, 6.3A Input Current Limit, 10ms Soft-Start and Battery Temperature Monitoring
SBM540 VIN VLOGIC 50k 50k 50k 50k 1F CLP SHDN CLN LT3651 ACPR TO CONTROLLER FAULT CHRG RT 54.9k CTIMER 0.68F RT TIMER BAT NTC ILIM RNG/SS GND BOOST 1N5819 SENSE RSENSE 24m CBAT 100F VIN SW 1F 3.3H RIL 16m CIN 22F TO SYSTEM LOAD
0.47F
NTC B 10k
+
BATTERY
3651 TA04
RELATED PARTS
PART NUMBER LT1511 LT1513 LT3650 DESCRIPTION 3A Constant Current/Constant Voltage Battery Charger SEPIC Constant or Programmable Current/Constant Voltage Battery Charger 2A Monolithic Li-Ion Battery Charger COMMENTS High Efficiency, Minimum External Components to Fast Charge Lithium, NIMH and NiCd Batteries, 24-Lead SO Package Charger Input Voltage May Be Higher, Equal to or Lower Than Battery Voltage, 500kHz Switching Frequency, DD-Pak and TO-220 Packages High Efficiency, Wide Input Voltage Range Charger, Time or Charge Current Termination, Automatic Restart, Temperature Monitoring, Programmable Charge Current, Input Current Limit, 12-Lead DFN and MSOP Packages Input Supply Voltage Regulation Loop for Peak Power Tracking in (MPPT) Solar Applications, Standalone, 4.95V VIN 32V (40V Abs Max), 1MHz, 2A Programmable Charge Current, Timer or C/10 Termination, 3mm x 3mm DFN-12 Package and MSOP-12 Packages Complete Charger for 1- or 2-Cell Li-Ion Batteries, Onboard Timer Termination, Up to 4A Charge Current, 10-Lead DFN and SO-8 Packages Complete Charger for 2-, 3- or 4-Cell Li-Ion Batteries, AC Adapter Current Limit and Thermistor Sensor, 16-Lead Narrow SSOP Package Complete Charger for 3- or 4-Cell Li-Ion Batteries, AC Adapter Current Limit, Thermistor Sensor and Indicator Outputs, 24-Lead SSOP Package Complete Charger for 2- to 6-Cell Li-Ion Batteries or 4- to 18-Cell Nickel Batteries, Up to 96% Efficiency, 20-Lead SSOP Package Complete Charger for 1- to 4-Cell Li-Ion Batteries or 4- to 18-Cell Nickel Batteries, Up to 93% Efficiency, 20-Lead (4mm x 4mm) QFN Package, LTC4009-1 for 4.1V Float Voltage, LTC4009-2 for 4.2V Float Voltage PowerPath Control, Constant-Current/Constant-Voltage Switching Regulator Charger, Resistor, Voltage/Current Programming, AC Adapter Current Limit and Thermistor Sensor and Indicator Outputs, 1 to 4-Cell Li, Up to 18-Cell Ni, SLA and SuperCap Compatible; 4mm x 4mm QFN-20 Package; LTC4012-1 Version for 4.1V Li Cells, LTC4012-2 Version for 4.2V Li Cells, LTC4012-3 Version Has Extra GND Pin
365142fa
LT3652
Power Tracking 2A Battery Charger
LTC4002 LTC4006 LTC4007 LTC4008 LTC4009/LTC4009-1 LTC4009-2
Standalone Li-Ion Switch Mode Battery Charger Small, High Efficiency, Fixed Voltage Li-Ion Battery Charger with Termination High Efficiency, Programmable Voltage Battery Charger with Termination 4A, High Efficiency, Multi-Chemistry Battery Charger High Efficiency, Multi-Chemistry Battery Charger
LTC4012/LTC4012-1/ 4A, High Efficiency, Multi-Chemistry LTC4012-2/LTC4012-3 Battery Charger with PowerPath Control
22 Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 FAX: (408) 434-0507
LT 0111 REV A * PRINTED IN USA
www.linear.com
LINEAR TECHNOLOGY CORPORA TION 2010

▲Up To Search▲

Price & Availability of LT3651-42

	To Download LT3651-42 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .